Shop With Confidence - 30 Day Easy Returns - No Need To Call
 
Follow us on facebook
 

SFI Roll Bar Padding for 1.62 to 2.00" Bar, 3 foot length

Click for a larger picture of SFI Roll Bar Padding for 1.62 to 2.00" Bar, 3 foot length
View Catalog Page in PDF format

SFI 45.1 Rated Roll Bar Padding has been proven to lessen impact forces transmitted to the head. It is highly recommended by SCCA and required by many other racing organizations. It is specifically recommended for use in areas where the helmet may contact the tubing.*

The half-round "C" shape covers one side of a tube between 1 5/8" and 2" diameter. The inside surface is lined with a peel-and-stick adhesive. We recommend backing up this adhesive with a few zip ties. Two pieces are shown in photo to illustrate inside and outside of padding. Approximately 1 inch thick in the center and 11/16" thick at the edges. 36 inch sections available in Black, Blue, or Red.

We also offer SFI Rated Roll Bar Padding for 1.125 - 1.5 Inch Diameter Tubing, Part No. 2391.

* Note: SFI-rated foam padding is designed for installation between the helmet and the roll bar. This padding is extremely stiff and rigid. It does not give except in very hard impacts. It is intended to cover only one side of the bar (the side between the bar and your helmet).

All other areas of the roll cage should be padded using softer High-Density Roll Bar Padding, Part No. 2390.

Enter desired order quantities below, then click the "Add selected quantities to cart" button.

Order Qty
Part No.
Desc.
Price
Status

2395-Black
Condition: New

Black SFI Roll Bar Padding, 3 foot length, 1.62 - 2.00" Bar

$16.99In Stock

2395-Blue
Condition: New

Blue SFI Roll Bar Padding, 3 foot length, 1.62 - 2.00" Bar

$16.99In Stock

2395-Red
Condition: New

Red SFI Roll Bar Padding, 3 foot length, 1.62 - 2.00" Bar

$16.99In Stock
 

Good product

5

Bought it for my Miata race car fits perfectly on the top of the Miata roll bar

Alex

Indy

Essential for any race car

5

Easy to cut and install, sticks great but I would recommend Zip ties every 8" or so as most series require.

vetteheadracer

Hudson, FL

true

Forms nicely with a heat gun

5

Chumpcar requires high density padding

Q

Crystal Lake, IL

true

Sticks on great

4

Sticks on great Make small cuts every half inch with a razor knife on the back side to allow it to go around a corner. Would be prefect if they had it available in other colors.

mogguy

Orlando, FL

true

Great Roll Bar Padding

5

Great price comparative to other SFI rated roll bar padding options. Sticks well and cuts easy.

JD

Houston, TX

true

Complies with the rules.

4

This roll bar padding is pretty stiff and took some careful planning and cutting to get it to cover as I wanted it to. The Tech service people at Pegasus recommended I cut it with my band saw which worked great. Don't just count on the glue to hold it in place, add a tie wrap about every 6 to 8 inches. I liked the ease of working with the lower density padding, but I now am rule compliant with this stiffer padding applied.

Zipper

Rochester, NY

true

good padding at a low price

5

Cheapest SFI rollbar padding I could find. As others commented it works great too.

pontoontodd

Loves Park IL

true

Quality replacement SFI Roll Bar Padding

5

Quality material, sticky adhesive, ditch the pool noodle foam and upgrade to SFI padding.

JohnK

Buffalo Grove, IL

true

Much better than what I've purchased elsewhere.

5

Great product and fast shipping as always. Have purchased padding elsewhere that was brittle with the adhesive backing dried up.

billbo46

Chicago

true

Great Product

5

Padding is excellent worked as advertise, delivered on time.

fassstone

Houston, TX, United States

true

SFI Roll Bar Padding for 1.62 to 2.00" Bar, 3 foot length

4.8 10

100.0