Order before 5:00 pm Central Time for Same Day Shipping on most In-Stock orders!
We carry a huge selection of Brake Parts!
 
 
 
 
Shop With Confidence - 30 Day Easy Returns - No Need To Call
 
Follow us on facebook
 

SFI Roll Bar Padding for 1.125" to 1.50" Bar, 3 foot length

Click for a larger picture of SFI Roll Bar Padding for 1.125" to 1.50" Bar, 3 foot length
View Catalog Page in PDF format

SFI 45.1 Rated Roll Bar Padding has been proven to lessen impact forces transmitted to the head. It is highly recommended by SCCA and required by many other racing organizations. It is specifically recommended for use in areas where the helmet may contact the tubing.*

The half-round "C" shape covers one side of a tube between 1 1/8" and 1 1/2" diameter. The inside surface is lined with a peel-and-stick adhesive. We recommend backing up this adhesive with a few zip ties. Two pieces are shown in photo to illustrate inside and outside of padding. Approximately 3/4 inch thick in the center and 1/2" thick at the edges. 36 inch sections available in Black, Blue, or Red.

We also offer SFI Rated Roll Bar Padding for 1.625 - 2.0 Inch Diameter Tubing, Part No. 2395.

* Note: SFI-rated foam padding is designed for installation between the helmet and the roll bar. This padding is extremely stiff and rigid. It does not give except in very hard impacts. It is intended to cover only one side of the bar (the side between the bar and your helmet).

All other areas of the roll cage should be padded using softer High-Density Roll Bar Padding, Part No. 2390.

Enter desired order quantities below, then click the "Add selected quantities to cart" button.

Order Qty
Part No.
Desc.
Price
Status

2391-Black
Condition: New

Black SFI Roll Bar Padding, 3 foot length, 1.12" - 1.50" Bar

$16.99In Stock

2391-Blue
Condition: New

Blue SFI Roll Bar Padding, 3 foot length, 1.125" - 1.50" Bar

$16.99In Stock

2391-Red
Condition: New

Red SFI Roll Bar Padding, 3 foot length, 1.125" - 1.50" Bar

$16.99In Stock
 

REVIEW SNAPSHOT®

by PowerReviews
SFI Roll Bar Padding for 1.125" to 1.50" Bar, 3 foot length
 
4.8

(based on 4 reviews)

Ratings Distribution

  • 5 Stars

     

    (3)

  • 4 Stars

     

    (1)

  • 3 Stars

     

    (0)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

100%

of respondents would recommend this to a friend.

Reviewed by 4 customers

Displaying reviews 1-4

Back to top

 
4.0

sticks on and stays on great

By mogguy

from Orlando, FL

Verified Buyer

Comments about SFI Roll Bar Padding for 1.125" to 1.50" Bar, 3 foot length:

Sticks on great Make small cuts every half inch with a razor knife on the back side to allow it to go around a corner. Would be prefect if they had it available in other colors.

 
5.0

Works great!

By 540

from OK

Verified Buyer

Comments about SFI Roll Bar Padding for 1.125" to 1.50" Bar, 3 foot length:

Firm, sticky, fits well.

 
5.0

Exactly what it's supposed to be

By Jimbo

from Alpena MI

Verified Buyer

Comments about SFI Roll Bar Padding for 1.125" to 1.50" Bar, 3 foot length:

Well it fits the rollcage tubes very well. Can't comment on how well it works (and hope I never can) because I haven't wrecked with it yet. Pegasus is a really good company to buy from giving quick delivery and even refunding part of the shipping charge when THEY found the actual cost was less than estimated.

 
5.0

Great SFI rollbar padding

By Puddin

from Albany, NY

Verified Buyer

Comments about SFI Roll Bar Padding for 1.125" to 1.50" Bar, 3 foot length:

Good size and fit for my 3/4 midget. Has 2 sided tape attached to it but i added zip-ties for additional holding power as I was putting it on 1.125" tubing. Would definitely purchase again when needed.

Displaying reviews 1-4

Back to top