We carry a huge selection of Competition Plumbing Parts!
 
 
 
Check us out on Instagram
 
Your IN STOCK source for quality racing supplies!
 
Follow us on facebook
 

Custom Hose Order Form for 825 PTFE Single Core Polyester Braided Hose, 8AN

Use this page to specify the length and type of hose ends to be installed on your custom-made hose. If you want more than one hose assembly made to the same exact specifications, you can also specify the quantity of hoses to be made. The default quantity is one. The prices of the hose ends shown below include the cost of installation and proof testing.

This custom hose assembly will be made using the following hose material:

Part No. 3495-08-INCH

825 PTFE Single Core Polyester Braided Hose, 8AN

See bottom of page for more information on this style of hose.

Quantity of hoses made to this exact specification:

Specify the length of the assembled hose: inches

The length of the hose assembly is measured to the center of the sealing surface (the flare for AN fittings). For banjo hose ends, the length is measured to the center of the banjo. The normal length tolerance is 0.25 inch plus 1% of the overall length (plus or minus). Minimum length is 6 inches. Maximum length is 240 inches.

Select Both Hose Ends from this list

Select End A

Select End B

Image

Part No.

Desc.

Price

Status

Click this thumbnail image to view a larger image

HE201-08-000  

-8 Swaged Hose End, 8AN Female Straight, Aluminum

$29.99 In Stock
Click this thumbnail image to view a larger image

HE201-08-045  

-8 Swaged Hose End, 8AN Female 45 Degree, Brazed Aluminum

$45.99 In Stock
Click this thumbnail image to view a larger image

HE201-08-090  

-8 Swaged Hose End, 8AN Female 90 Degree, Brazed Aluminum

$45.99 In Stock
Click this thumbnail image to view a larger image

HE201-08-120  

-8 Swaged Hose End, 8AN Female 120 Degree, Brazed Aluminum

$65.99 In Stock
Click this thumbnail image to view a larger image

HE201-08-150  

-8 Swaged Hose End, 8AN Female 150 Degree, Brazed Aluminum

$64.99 In Stock
Click this thumbnail image to view a larger image

HE201-08-180  

-8 Swaged Hose End, 8AN Female 180 Degree, Brazed Aluminum

$65.99 In Stock
Click this thumbnail image to view a larger image

HE205-08-045  

-8 Swaged Hose End, 8AN Female 45 Degree Swivel, Aluminum

$64.99 In Stock
Click this thumbnail image to view a larger image

HE205-08-090  

-8 Swaged Hose End, 8AN Female 90 Degree Swivel, Aluminum

$64.99 In Stock
Click this thumbnail image to view a larger image

HE205-08-120  

-8 Swaged Hose End, 8AN Female 120 Degree Swivel, Aluminum

$75.99 In Stock
Click this thumbnail image to view a larger image

HE205-08-150  

-8 Swaged Hose End, 8AN Female 150 Degree Swivel, Aluminum

$75.99 In Stock
Click this thumbnail image to view a larger image

HE205-08-180  

-8 Swaged Hose End, 8AN Female 180 Degree Swivel, Aluminum

$75.99 In Stock

Specify Fitting Alignment:

Important Note: It can be very difficult to determine the fitting alignment without trial and error. When bends are introduced to the hose, the apparent orientation can change significantly. Two methods can be used to avoid having to worry about fitting alignment:

  1. At least one end of the hose should have a straight fitting.
  2. If both ends of the hose require angled fittings, at least one of them should be a swivel fitting (Fitting Part No. starts with HE205). It usually is not necessary to use a swivel fitting at both ends. One end can use the less expensive standard fitting (Fitting Part No. starts with HE201).

If either of these two methods is used, just leave the alignment at the 0° default value.

Fitting Alignment Illustration

Detailed Description of Hose Material

Part No. 3495 -08 -INCH

825 PTFE Single Core Polyester Braided Hose, 8AN - per inch

Goodridge G-Max 825 was developed as a low-cost fuel hose that is compatible with all types of fuel. It is lighter than stainless-braided 811 hose (and much lighter than conventional rubber-lined hose), but considerably less expensive than aramid-braided 910 hose.

The anti-static PTFE liner is compatible with all types of fluids and ALL types of fuel (gasoline, diesel, E85, alcohol, and nitromethane). It is also fully resistant to fuel vapor penetration, which means it will not emit a fuel smell. The hose ends (sold separately) require no special tooling to assemble, so you can build hoses at home. The black polyester outer braid looks great in any engine bay. The lining is smooth inside and out to keep the cost down; however, this makes 825 hose less flexible than the semi-corrugated 910 hose. It also results in lower pressure and vacuum ratings than the 910 type.

Note: This hose is only compatible with our 811 Tube-Style AN Hose Ends (Part No. 3481) or 811 Forged AN Hose Ends (Part No. 3484). It is not compatible with any other hose ends, and cannot be clamped on a hose barb!

Hose Assembly Instructions for Type 825 Hose

Type 825 Polyester Braided Racing Hose
Hose
Size
Hose I.D.
(Inches)
Hose O.D.
(Inches)
Operating
Pressure
Min. Bend
Radius
Weight
per ft
-8 0.50" 0.68" 464 psi 3" 1.50 oz
-10 0.63" 0.83" 406 psi 4" 2.19 oz
-12 0.75" 0.95" 305 psi 5.00" 2.52 oz

Temperature range -40°C to 110°C (-40°F to 230°F). Not recommended for oil or coolant systems because of the temperatures involved.

Note: This hose is not for use inside the cockpit! SCCA rules mandate metal tubing or metal-braided hoses inside the cockpit. This hose is not NHRA approved.