Pegasus Auto Racing Supplies
Your In-Stock Source since 1980
| Today's Featured Items | |||
|---|---|---|---|
|
Dated 2031! Sabelt Steel Series S622 Saloon 2x2 FIA Harness, Pull Up  The Sabelt CCS622S is an FIA 8853-2016 approved 6-point 2x2 camlock harness. It is designed for racing sedans where the driver is wearing a HANS Device. |
Facet Cylindrical 12v Fuel Pump, 1/8 NPT, 4-5 psi The Facet 40131 Cylindrical 12 Volt Fuel Pump delivers a maximum flow of 36 GPH or 4-5 psi max pressure. 1/8 NPT female ports. |
OBP Pro-Race 3-Pedal Box, Floor Mount, without MC The OBP Pro Race 3-pedal assembly includes Clutch, Brake, and Throttle pedals in one unit. The "Floor Mount" configuration mounts to the floor pan with the master cylinders positioned in front of the pedals. | |
811 PTFE Lined Stainless Steel Braided Racing Hose Goodridge 811 is a flexible, lightweight stainless braided hose developed for pro racing. The PTFE liner is compatible with all fluids and resists fuel vapor penetration. |
Black Silicone Hose, 5/8" I.D. 90 degree Elbow, 6" Legs Our silicone hoses are designed for coolant plumbing. This 3-ply reinforced Black 90 Degree Elbow has 6 inch legs. 16mm nominal ID fits over 5/8 inch OD tube. |
Weber Emulsion Tube, DCOE, IDF, IDA Dual These calibrated Weber Emulsion Tubes fit the common Weber DCOE, IDF, and 48 IDA (Dual) carburetors. | |
Setrab Series 6 Oil Cooler, 19 Row, M22 Ports Setrab oil coolers have a brazed aluminum construction that provides maximum cooling capacity in the smallest possible space, with minimal pressure drop. |
Racetech Multi-Temperature Indicating Stickers Racetech temperature stickers measure and document peak temps on radiators, oil tanks, shocks, and more. Permanent color changes from 99F to 536F. |
Quick Release Seat Back Brace For non-FIA seats, a back brace is required by SCCA, provides additional support and works easily with multi driver cars. | |
Totim Racing Self-Contained Foam Seat Insert Kits, LMP / F4 Totim has changed the custom fit seat game! This product uses expandable foam in a sealed bag to form fit to your body in your seat, within minutes, not hours! |
Canton EPC Pro Electric Valve Kit for Accusump, 20-25psi The Accusump EPC Valve Kit makes operation of the Accusump even easier. When oil pressure drops below 15 psi, the accumulated pressurized oil in the Accusump is delivered to the engine. |
KOUL Tools - Hose Assembly Tool (specify kit size) Assemble stainless braided hose in less than 10 seconds with KOUL Tools! Just put the socket in the tool and twist the hose in. It can pay for itself the first time you save a frayed-out hose. | |
MyLaps TR2 Rechargeable Car / Motorcycle Transponder, 1 Year The red MyLaps TR2 Transponder replaces the rechargeable X2 and TranX 260 for cars and motorcycles. Manage your 1-year subscription in the Speedhive app on your smartphone. |
Lacing Cord, MIL-T-43435B, specify color Lacing Cord is used to assemble aircraft and military wiring looms. Flat braided nylon tape is lighter than zip ties and does not add significantly to the harness diameter. |
45mm (1 3/4 inch) Pegasus Pro Design Aluminum Hose Joiner Use our 1 3/4 inch OD anodized aluminum joiner to connect any two 45mm ID silicone hoses - an elbow to a straight section, two elbows, or a reducer to an elbow. | |
Staubli SPT08 Non-Spill Quick-Disconnect Plug Staubli SPT08 series clean-break dry disconnect plugs are ideal for fuel lines. The seals are compatible with virtually every racing fuel, from gas to alcohol. |
1/8 NPT Brake Bleeder Assembly (2 piece) Our 2-Piece 1/8 NPT Brake Bleeder is a direct replacement for Wilwood caliper bleeder assemblies. The outer sleeve has an internal seat for the bleeder screw. |
Lifeline Weld-On 3 Hole Quick Release Steering Hub, FIA Our 3-Hole Quick Release Steering Hub has an asymmetric spline that allows mating in only one orientation. You will never end up with a cock-eyed steering wheel! | |
High Temp Silicone 2-ply Air Duct Hose, 450F, Orange Only This High Temperature 2-Ply Silicone Air Duct Hose is popular for brake cooling ducts and withstands a higher pressure and vacuum than a Single-Ply Silicone Air Duct Hose does. |
AiM Fluid/Air Pressure Sensor, 0-15 psi, 1/8 NPT This AiM sensor reads between 0-15PSI, using 1/8NPT thread to secure it into the fluid or air ports. |
Safety Retaining Washer for Rod End Bearings Most racing groups require Safety Retaining Washers on rod end bearings in case the ball separates from the housing. We offer washers in SAE and metric sizes. | |
Top Quality, Huge Selection and Very Competitive Prices on Silicone Hose
Nearly 1,000 different part numbers are now in stock from 1/2 inch to 6 inch inside diameter. Available in black, blue or red. Save on our durable, heat-resistant, high-quality Silicone Hose. Great for coolant or turbo intake plumbing. We make it easy to find the hoses that you need:  Gates PowerGrip Hose Clamps |
Congrats to Jeff Oglesby of Spanish Fort Alabama
Jeff is the most recent winner in our $5,000 sweepstakes. Every time you place an order you'll be entered. No purchase necessary. Other past winners include: Jason Vinkemulder of Mason MI |
Special Message for International Customers
Export orders make up a significant portion of our sales. Because of our high volume of international shipments, we have been able to negotiate reduced rates for expedited shipping to foreign destinations. Information on International Shipping
Pegasus Supports Racing2004 thru 2026 SCCA Runoffs® Contingency Sponsor 2012 thru 2026 Vintage Sports 2000 Series Sponsor 2014 thru 2026 Formula 600 Challenge Series Sponsor VSCDA Driver's School Sponsor NSSCC Driver's School Sponsor and many other events | |
| New: Take a Virtual Tour of our Showroom and Warehouse (go through the double doors to the left of the Hawk banner to get to the warehouse) |
|---|
Pegasus is located at 2475 S. 179th Street, New Berlin WI 53146 USA
In addition to our large warehouse, we also have a small showroom and customer service counter. If you're in the area, feel free to stop by!