Pegasus Auto Racing Supplies
A 100% employee owned company
| Today's Featured Items | |||
|---|---|---|---|
Quick-Disconnect Socket to 12AN Hose Barb, 5000 Series This Jiffy-Tite 5000 Series Quick-Disconnect socket has a barb to accept a 12AN hose. Buna seals for gas, oil, water, and coolant. 200psi max pressure. |
Aurora PTFE Lined Rod End Bearings, Special Sizes Many race car constructors used rod ends from various manufacturers with non-standard size combinations. We stock high-quality Aurora rod ends made in the USA. |
Camloc 27S3 Light Duty Stud, Flush Head, Cross Recess These light-duty Camloc flush head cross recessed studs are rated for 200 pounds working strength. The Phillips (cross) head allows quick use with standard #2 Phillips screwdrivers. | |
Slide Type Captive Hood Pin Assembly- Set of 2 Never drop or lose another hood pin! The spring loaded clevis pins stay attached to the retainer plates. They're also much easier than conventional hood pins to fasten in a hurry. Sold in pairs. |
Safety Retaining Washer for Rod End Bearings Most racing groups require Safety Retaining Washers on rod end bearings in case the ball separates from the housing. We offer washers in SAE and metric sizes. |
Small NACA Duct (1 Outlet), for 2.5" Hose Extensive engineering went into these small NACA ducts resulting in maximum air flow with minimal drag. They are molded from tough, high-impact plastic for easy installation. | |
Redhead 2.0" Push-Pull Refueling Valve, Male Probe Redhead valves were designed over 30 years ago to refuel Indy cars without spillage. This male probe valve attaches to your refueling rig and connects to the female receptacle. |
AiM SmartyCam3 Corsa, 67 degree Lens, 5-pin CAN (Exp) Cable All the same features as a SmartyCam 3, but no more expansion needed! Wire directly to your dash or ECU. Standard 67* lens. Also features 60FPS. |
3AN Bulkhead Mount for 3/8-24 Bleeder Screw, Stainless Steel This 3AN Bulkhead mount for a 3/8-24 bleeder screw has a male 3AN bulkhead thread for easy mounting into a panel or bracket while accepting a standard 3AN hose end. | |
Stainless Steel Worm-Drive Hose Clamp with Metal Lining Our hose clamps prevent extrusion of silicone hose through the slots. A smooth non-perforated metal band lines the inside to prevent hose damage. |
Fuel Hose, 2" I.D. 45 degree Elbow, 6" Legs Our special 2"(51mm)ID 45 degree 1 ply black silicone elbow has a fuel and oil-resistant fluorocarbon rubber (FKM) inner liner making it ideal for use in low pressure fuel and oil applications. |
GKN Tripod Joint Grease, 300 Gram Tube This genuine GKN Tripod Joint Grease is designed specifically for use in tripod joints. Using the wrong grease can lead to overheating and premature failure. | |
Creafoam Bead Seat Kit Make your own professional-quality custom-fitted racing seat insert with our Creafoam Bead Seat Kits! These complete kits are easy to use. All you need to add is a vacuum, a seat, and a driver. |
Cartek GT Battery Isolator Kit with Red External Button The Cartek GT Battery Isolator is an FIA-approved solid-state electrical master kill switch that eliminates long, heavy battery cables. Includes red trigger button. |
Black Aluminum Barbed Hose Fitting to AN Female Our black anodized aluminum barbed hose ends allow you to use standard AN fittings with rubber hose. Each hose end has a standard female AN at one end and a hose barb at the other. | |
Optimate Test 12v Cranking and Alternator Tester The compact OptiMate Test Cranking and Alternator Tester can save you from being stranded on a road trip! See the state of your battery and charging system in 15 seconds. |
MS21042 Style B Jetnut, All Metal Locknut MS21042 Jetnuts are all-metal, self-locking nuts rated for temperatures to 450F. The reduced hex size makes them ideal for tight applications where wrench access is a problem. |
Tilton 74 Series Universal Master Cylinder Kit The Tilton 74 Series Master Cylinder Kit includes large and small reservoirs. The reservoirs make fluid level inspection easy. The hard anodized aluminum body makes for a long life. | |
Facet Dura-Lift 12v Fuel Pump, 1/8 NPT, 9-11 psi, 120" lift The Facet 40222 Dura-Lift Fuel Pump can draw fuel from up to 10 feet away. Great replacement for the lift pump on 83-94 Ford diesel trucks and vans. |
Sabelt Aluminum Seat Frame Mounting Bracket, Standard Length These FIA-approved standard length Sabelt seat brackets fit most side mount racing seats. They are 15-1/2" long with a perfect 90 degree bend and are made from 5mm thick black epoxy coated aluminum. |
Setrab 12V Mini Gear Oil Circulation Pump, AN8, 150 Filter This self-priming helical gear pump from Setrab is designed for transmission and differential oil cooling. Built-in mounting bracket with vibration dampers. Includes 8AN fittings with 150 micron inlet filter. | |
Top Quality, Huge Selection and Very Competitive Prices on Silicone Hose
Nearly 1,000 different part numbers are now in stock from 1/2 inch to 6 inch inside diameter. Available in black, blue or red. Save on our durable, heat-resistant, high-quality Silicone Hose. Great for coolant or turbo intake plumbing. We make it easy to find the hoses that you need:  Gates PowerGrip Hose Clamps |
Congrats to Jason Vinkemulder of Mason Michigan
Jason is the most recent winner in our $5,000 sweepstakes. Every time you place an order you'll be entered. No purchase necessary. Other past winners include: Sean McGray of Las Vegas NV |
Special Message for International Customers
Export orders make up a significant portion of our sales. Because of our high volume of international shipments, we have been able to negotiate reduced rates for expedited shipping to foreign destinations. Information on International Shipping
Pegasus Supports Racing2004 thru 2024 SCCA Runoffs® Contingency Sponsor 2012 thru 2024 Vintage Sports 2000 Series Sponsor 2014 thru 2024 Formula 600 Challenge Series Sponsor VSCDA Driver's School Sponsor NSSCC Driver's School Sponsor and many other events | |
| New: Take a Virtual Tour of our Showroom and Warehouse (go through the double doors to the left of the Hawk banner to get to the warehouse) |
|---|
Pegasus is located at 2475 S. 179th Street, New Berlin WI 53146 USA
In addition to our large warehouse, we also have a small showroom and customer service counter. If you're in the area, feel free to stop by!
Click the above photo for a behind the scenes look at our warehouse expansion project.